68K cycle timing test ROM?

Ask anything your want about Megadrive/Genesis programming.

Moderator: BigEvilCorporation

Post Reply
Near
Very interested
Posts: 109
Joined: Thu Feb 28, 2008 4:45 pm

68K cycle timing test ROM?

Post by Near » Tue Jun 04, 2019 3:06 am

Does there exist a test ROM that validates the cycle timings of 68K instructions?

The timing documents out there are a bit tough to read, and even tougher to verify for every instruction given the way my core tries to move each cycle penalty to exactly where it's used (eg inside the bus read/write handlers, inside the effective address pre-decrement code, etc.)

I would prefer a Genesis test ROM, but if there's one for no real specific CPU architecture (eg I won't have to emulate an entire Amiga or Neo Geo), that would also be great.

Really hoping something like this exists ...

Nemesis
Very interested
Posts: 791
Joined: Wed Nov 07, 2007 1:09 am
Location: Sydney, Australia

Re: 68K cycle timing test ROM?

Post by Nemesis » Wed Jun 05, 2019 7:00 am

Kinda. If you want to be able to verify perfect cycle accuracy for all bus timings for all instructions, you're out of luck. I did work on making one that measured bus timings within an opcode for particular sets of instructions, but getting repeatable, stable results out of it while avoiding infinite spirals of death was hard. You've got to remember that on the Mega Drive, bus cycles are being stolen for RAM refresh. My technique involved watching for torn reads on hcounter transition points to set a known base point to the cycle, then spinning repeated instructions keyed off hcounter to fill a few KB of results, and taking a high/low measure of the counter change and comparing it to measured values from the system. This required sub-cycle timing accuracy, RAM refresh cycle, and hcounter torn reads to be supported in order to pass in an emulator. Problem was, it only worked (on hardware) about 98% of the time, and I wasn't happy with that. I shelved it late last year. I could dust it off and see where it ended up.

Apart from that, there are a few things out there to measure timing over large spans of opcodes (IE, execute 1000 instructions and take a measure), but they're not overly helpful as you can't easily narrow down where things went wrong, and the RAM refresh cycles throw things off as I mentioned.
Last edited by Nemesis on Wed Jun 05, 2019 10:24 am, edited 1 time in total.

Nemesis
Very interested
Posts: 791
Joined: Wed Nov 07, 2007 1:09 am
Location: Sydney, Australia

Re: 68K cycle timing test ROM?

Post by Nemesis » Wed Jun 05, 2019 7:03 am

All that said, I see the Microcode analysis (viewtopic.php?f=2&t=3023) as the way forward. Reading the microinstructions tells you what you need to know regarding cycle timing. I hope to extract simple, verified data tables at the end of that process to make things easier for everyone, but ultimately I think that's a more logical route right now than hardware testing. The alternative is probably driving the 68000 with a microcontroller or FPGA and sampling timing for every instruction variation, then sticking your 68000 core in a similar software-defined box and comparing with the expected results.

Near
Very interested
Posts: 109
Joined: Thu Feb 28, 2008 4:45 pm

Re: 68K cycle timing test ROM?

Post by Near » Wed Jun 05, 2019 12:27 pm

The RAM refresh does indeed sound like a challenge. At least on the SNES, the RAM refresh is predictable and easy to test instruction timings around it. I haven't looked into how to emulate the version on the Mega Drive yet.

Perhaps we could use a timing test ROM for a 68K system that doesn't use DRAM, if one even exists? As long as I don't have to emulate an entirely new system and video chipset to get the results ...

A coarse test is fine as well. I guess the best I can do for now is to build a little framework that tries to generate those weird A(B/C) tables that are all the rage on the 68K. But they're a bit hard to read.

For instance: https://wiki.neogeodev.org/index.php?ti ... ns_timings
What do the colors mean inside each cell?
The DIV algorithm isn't defined. MULS sounds ... really weird.
Bit manipulation has an "* indicates maximum value" note, but doesn't explain what that means.
Etc.
Does anyone here know how to get in touch with Olivier Galibert?
We ping each other on Twitter on occasion. @o_galibert.

Sik
Very interested
Posts: 939
Joined: Thu Apr 10, 2008 3:03 pm
Contact:

Re: 68K cycle timing test ROM?

Post by Sik » Wed Jun 05, 2019 3:35 pm

…the 68000 user manual doesn't give vague "maximum value", look into that (section 8, if you wonder where the timings are). The only one where it's vague is with division (it just says it's around 140 cycles), and I think that's in large part because the underlying algorithm is complex enough that an exact estimation would be hell to explain. BlastEm actively attempts to emulate the algorithm proper, may want to look at that code (m68k_core_x86.c seems to have the implementation in it at least? as divu()/divs()).
Sik is pronounced as "seek", not as "sick".

Eke
Very interested
Posts: 885
Joined: Wed Feb 28, 2007 2:57 pm
Contact:

Re: 68K cycle timing test ROM?

Post by Eke » Wed Jun 05, 2019 6:39 pm

You can also find an implementation of DIVU/DIVS timings here: http://pasti.fxatari.com/68kdocs/

Also, if you are not already aware, there are also some timings errors in M68K User Manual that are corrected in YACHT.txt document: http://nemesis.hacking-cult.org/MegaDri ... /Yacht.txt

I recently noticed one of these fixed instruction had some noticeable effect on one MD game (Clue) once you implement accurate VRAM access (FIFO/DMA) timings as it is massively used in a big loop executed just before some VRAM routines that can cause screen corruption if started too close from Vint. This part is very timing sensitive and might break each time you start improving emulation timings (like adding periodic bus refresh delays) if some of your other timings are off... or get fixed because of inaccurate timings emulation.

ijor
Interested
Posts: 15
Joined: Fri Nov 16, 2018 11:46 am

Re: 68K cycle timing test ROM?

Post by ijor » Wed Jun 05, 2019 8:52 pm

byuu wrote:
Tue Jun 04, 2019 3:06 am
Does there exist a test ROM that validates the cycle timings of 68K instructions?
...
I would prefer a Genesis test ROM, but if there's one for no real specific CPU architecture (eg I won't have to emulate an entire Amiga or Neo Geo), that would also be great.
I can't comment about the Genesis, but I doubt there is a generic test suit like that. How would you measure cycles without some specific hardware?

Anyway, in the first place, I recommend you check the official Motorola documentation that is comprehensive and later versions are very accurate (do have a couple mistakes).

As somebody recommended, get YACHT. It still has a couple of mistakes, but it is very complete and includes bus access timing, not just number of cycles.
The DIV algorithm isn't defined. MULS sounds ... really weird.
MUL timing might sound weird, but it is accurate as documented. It has to do with how the microcode works.

There is no simple formula for computing DIV timing. Get the sources I published years ago for code that computes the exact timing.
Bit manipulation has an "* indicates maximum value" note, but doesn't explain what that means.
If the bit is located in the lowermost word (bit number < 16), then it is two cycles less.
Sik wrote:
Wed Jun 05, 2019 3:35 pm
…the 68000 user manual doesn't give vague "maximum value"
It does. At least the version I have.
http://github.com/ijor/fx68k (68000 cycle accurate FPGA core)

Near
Very interested
Posts: 109
Joined: Thu Feb 28, 2008 4:45 pm

Re: 68K cycle timing test ROM?

Post by Near » Fri Jun 07, 2019 10:42 am

http://nemesis.hacking-cult.org/MegaDri ... /Yacht.txt

For whoever maintains this, there's a typo on line 579 for CLR <ea>.B/.W:

Code: Select all

    (xxx).L       |  8(1/1) 12(2/0) |   np np    nr |               np nw       
It should be 8(1/1) 12(3/0). One of the read cycles is missing.

Nemesis
Very interested
Posts: 791
Joined: Wed Nov 07, 2007 1:09 am
Location: Sydney, Australia

Re: 68K cycle timing test ROM?

Post by Nemesis » Fri Jun 07, 2019 1:06 pm

It originated from a guy on http://www.atari-forum.com. I'm not sure he really maintains it anymore, but he's still active there. You can find him in this recent thread talking about it: http://www.atari-forum.com/viewtopic.php?t=36648

Near
Very interested
Posts: 109
Joined: Thu Feb 28, 2008 4:45 pm

Re: 68K cycle timing test ROM?

Post by Near » Sun Jun 09, 2019 2:36 pm

Slowly working through yacht still ... had to emulate the prefetch to make sense of JMP/JSR timings. The trick is JMP (d16,An) can peek ahead to IRC without having to fetch another byte, whereas JMP (An) has no use for it, hence why they're both 8(2/0).

Question though: what is the purpose of IRD?

http://pasti.fxatari.com/68kdocs/68kPrefetch.html
1) Load IRC from external memory. <reset only>
2) Transfer IRC to IR.
3) Reload IRC from external memory.
4) Transfer IR to IRD.
According to this, IRD will always be equal to IR. Is there any reason for an emulator to have an IRD, or is that just a detail for microcode/transistor-level simulation?

ijor
Interested
Posts: 15
Joined: Fri Nov 16, 2018 11:46 am

Re: 68K cycle timing test ROM?

Post by ijor » Mon Jun 10, 2019 2:59 am

byuu wrote:
Sun Jun 09, 2019 2:36 pm
Question though: what is the purpose of IRD?
http://pasti.fxatari.com/68kdocs/68kPrefetch.html
1) Load IRC from external memory. <reset only>
2) Transfer IRC to IR.
3) Reload IRC from external memory.
4) Transfer IR to IRD.
According to this, IRD will always be equal to IR. Is there any reason for an emulator to have an IRD, or is that just a detail for microcode/transistor-level simulation?
IR is used for decoding the next instruction. IRD holds the opcode currently being executed. They have the same content most of the time, but not always. The above steps are not performed all at the same cycle. IR and IRD are never loaded at the same microinstruction. That means that IR changes at least two cycles before IRD.

e.g, during instructions that takes four cycles (like NOP), two cycles IR and IRD will be the same, two cycles might be not (depending if the next instruction has the same opcode or not).
http://github.com/ijor/fx68k (68000 cycle accurate FPGA core)

mickagame
Very interested
Posts: 256
Joined: Sat Jun 07, 2008 7:37 am

Re: 68K cycle timing test ROM?

Post by mickagame » Wed Jan 27, 2021 12:06 pm

What could be the reference document in 2021 for 68k timings?
I'l trying to write a 68k core and need a good documentation to implement correct timings.

Post Reply